Operating Instructions & Parts Manual
MagicLift™ Service Jack, Low Profile
Capacity
Model
29023
29025
2 Ton
2 Ton
29023
29025
U.S. Patent No’s. 6,199,379 • 5,946,912
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
! ADVERTENCIA
! WARNING
To avoid crushing and related injuries:
NEVER work on, under or around
• Leer, comprender, y seguir las instrucciónes antes
de utilizar el aparato.
•
• El manual de instrucciónes y la información de
seguridad deben estar comunicado en lengua del
operador antes del uso.
a load supported only by a hydraulic
jack.
•
ALWAYS use adequately rated jack
stands.
• No seguir estas indicaciónes puede causar daños
personales o materiales.
SFA Companies
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
Printed in China
29023-M2 rev 0710
PREPARATION
Assembly
Insert handle into the handle sleeve. Tighten the bolt on handle sleeve to prevent accidental removal of handle while
in use.
Before Use
1. Verify that the product and the application are compatible, if in doubt call Omega Technical Service (888) 332-
6419.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. To familiarize yourself with basic operation of this jack, locate and turn the release valve (handle):
a. Clockwise until firm resistance is felt to further turning. This is the ‘CLOSED’ release valve position used to
raise the load.
b. Counter-clockwise, but no more than 1/2 full turn from the closed position. This is the ‘OPEN’ release valve
position used to lower the load.
4. Check to ensure that jack rolls freely. Raise and lower the unloaded saddle throughout the lifting range before
putting into service to ensure the pump operates smoothly.
5. Replace worn or damaged parts and assemblies with Omega authorized replacement parts only. Lubricate as
instructed in Maintenance Section.
Bleeding / Venting Trapped Air of Model 29025
With the release valve in the OPEN position (3b.) and with saddle fully lowered, locate and remove the oil filler
plug. Pump 6 to 8 full strokes. This will help release any pressurized air which may be trapped within the reservoir.
Reinstall the oil filler plug.
Handle
Lifting Arm
Saddle
Oil Filler Plug
(under cover plate,
on reservoir)
Handle Sleeve
Front Wheel
Rear Caster
Figure 2 - Model 29025 Nomenclature
3
! WARNING
! WARNING
• Study, understand, and follow all printed
materials provided with/on this product before use
.
X
• Do not exceed rated capacity.
• Use only on hard, level surface.
• This is a lifting device only!
To avoid crushing and related injuries:
•
Never work on, under or around a load supported
only by hydraulic jack.
• Immediately after lifting, support the load with
a pair of appropriately rated jack stands.
•
Always use adequately rated jack stands.
• Lift only on areas of the vehicle as specified by
the vehicle manufacturer.
• Chock each unlifted tire in both directions.
•
Do not move or dolly the vehicle while on the jack.
• Do not use this device to lift, level, lower, support
nor move a house, mobile home, travel trailer,
camper or any building structure.
• No alterations shall be made to this product.
• Failure to heed these markings may result in
• Be alert and sober when using this product. Do not
personal injury and/or property damage.
operate under the influence of drugs or alcohol.
OPERATION
Lifting
Only attachments and/or adapters supplied by the manufacturer shall be used. Lift only on area of the
vehicle as specified by the vehicle manufacturer.
!
1. Follow the vehicle manufacturer’s recommended guidelines for lifting. Engage the emergency brake and chock
each unlifted wheel in both directions to prevent inadvertent vehicle movement.
2. Close the release valve by turning the handle clockwise until firm resistance is felt.
3. Refer to the vehicle manufacturer owner’s manual to locate approved lifting points on the vehicle. Center jack
saddle under lift point.
4. Verify lift point, then pump handle to contact lift point. To lift, pump handle until load reaches desired height.
5. Transfer the load immediately to appropriately rated jack stands.
NEVER use hydraulic jack as a stand alone device! ALWAYS transfer the lifted load IMMEDIATELY to a
pair of appropriately rated jack stands. Use one pair of jack stands per vehicle. Rated capacity is per
pair only! Do not exceed rated capacity.
!
Lowering
Be sure all tools and personnel are clear before lowering load. Slowly open the release valve! The more
you turn the handle counter-clockwise, the faster the load will come down. Maintain control of the rate
of speed at which the load lowers at all times!
!
1. Raise load high enough to clear the jack stands.
2. Remove jack stands carefully (always used in pairs).
3. Slowly turn the handle counter-clockwise, but no more than 1/2 full turn. If the load fails to lower:
a. Use another jack to raise the vehicle high enough to reinstall jack stands.
b. Remove the malfunctioning jack and then the jack stands.
c. Use the functioning jack to lower the vehicle.
4. After removing jack from under the load, fully lower the saddle to reduce ram exposure to rust and
contamination.
4
MAINTENANCE
Use only Mobil DTE 13M or equivalent
Lubrication
!
hydraulic jack oil. Improper fluid can cause
premature failure of the jack and the potential for sudden
and immediate loss of load.
A periodic coating of light lubricating oil to pivot points,
axles and hinges will help to prevent rust and assure that
wheels, casters and pump assemblies move freely.
Adding oil
Cleaning
It is difficult to confirm the correct oil level by simply
looking into the oil reservoir after removing the vent
screw. *Correct oil level allows the saddle to reach its
advertised maximum height and its advertised minimum
height.
Periodically check the pump piston and ram for signs
of rust or corrosion. Clean as needed and wipe with
an oily cloth.
Note: Never use sandpaper or abrasive material on
these surfaces!
Too much oil will not allow the saddle to lower
completely.
Too little oil will not allow the saddle to raise
completely.
•
•
Storage
When not in use, store the jack with saddle fully
lowered.
1. With saddle fully lowered set jack in its upright,
level position. Remove vent screw (29023), oil plug
(29025).
2. *Fill until oil nearly covers the inner cylinder as seen
from the oil filler hole. Reinstall the vent screw, oil
plug.
Changing oil
For best performance and longest life, replace the
complete fluid supply at least once per year.
1. With saddle fully lowered set jack in its upright,
level position. Remove vent screw (29023), oil plug
(29025).
2. Lay the jack on its side and drain the fluid into a
suitable container.
Note. Dispose of hydraulic fluid in accordance with
local regulations.
3. *Fill until oil nearly covers the inner cylinder as seen
from the oil filler hole. Reinstall the vent screw, oil
filler plug.
TROUBLESHOOTING
Symptom
Possible Causes
Corrective Action
Jack will not lift load
• Release valve not tightly closed
• Load is too heavy
• Ensure release valve tightly closed
• Consider higher capacity jack
Jack will lift, but not maintain
pressure
• Ensure release valve tightly closed
• Discontinue use, contact Omega
Technical Service
• Release valve not tightly closed
• Hydraulic unit malfunction
Jack will not lower after unloading • Reservoir overfilled
• Linkages binding
• Drain fluid to proper level
• Clean and lubricate moving parts
Poor lift performance
• Fluid level low
• Hydraulic unit malfunction
• Ensure proper fluid level
• Discontinue use, contact Omega
Technical Service
Will not lift to full extension
• Fluid level low
5
• Ensure proper fluid level
REPLACEMENT PARTS (refer to page 7)
Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and
position in the assembly sequence. When ordering parts, give Model number, serial number and parts description.
Call or write for current pricing: SFA Companies, 10939 N. Pomona Ave. Kansas City, MO 64153, USA.
Replacement Parts Illustration for model 29023
12
13
1
2
3
24
k
10
q
j
23
i
r
l
p
o
h
n
g
m
b
f
e
11
20
21
25
6
d
9
c
8
22
19
b
18R
a
18L
16 17
5
15
14
7
4
Figure 3 - Replacement Parts Illustration for Model 29023
6
Replacement Parts List for model 29023
Item#
1
Part#
Description
Qty.
1
1
1
2
2
1
1
1
1
1
1
2
1
2
2
1
4
1
1
2
1
1
1
1
1
1
1
G86301-0001
G86301-0017
G86308-0001
G86301-0004
G86301-0003
G86301-0008
G86301-0019
G86308-0003
G48900-0024
G86308-0004
G86301-0014
G86301-0012
G86308-0005
G86301-0023
G86301-0024
G88009-0016
G86301-0032
G59509-0016
G59509-0015
G59305-0006
G73500-0011
G73500-0012
G59305-0005
G69400-0004
G69400-0003
G73500-0010
G86308-0000
Saddle Pad
2
Saddle
3
Hydraulic Unit
Front Wheel Assembly
Rear Caster Assembly
Handle Grip
4
5
6
7
Handle Assembly
Handle Sleeve
Bolt, M10x16
8
9
10
11
12
13
14
15
16
17
18R
18L
19
20
21
22
23
24
25
**
U-joint
Vent Screw
Return Spring, Lift Arm
Cover
Nut, M16
Spring Washer, D16
Bolt, M12
Nut, M12
Bolt, Handle Sleeve, RH side
Bolt, Handle Sleeve, LH side
Spring Washer, D20
Pin D12
Roller
Spring Washer, D10
Spring Pin
Cap, Pump Piston
Return Spring, Handle
Seal Kit (includes a thru r)
-
-
29023-M1
Manual
-
-
29023-L0
Label
**Repair Kit Contents:
Item
Description
Qty
1
Item
Description
Qty
1
a
b
c
d
e
f
O-ring
j
Back-up Washer
O-ring 13x2.4
O-ring 8x1.8
O-ring
O-ring
2
k
l
1
Back-up Washer
U-cup
1
1
1
m
n
o
p
q
r
1
Back-up Washer
O-ring
1
Back-up Washer
O-ring 17x2.65
Back-up Washer
Back-up Washer
Oil Seal
1
1
1
g
h
i
O-ring
2
1
Washer, Metal
Oil Seal
2
1
1
1
(**) Replacement requires special skills, knowledge, and equipment. Only an authorized service center may
perform the repair and/or replacement of these items.
7
REPLACEMENT PARTS (refer to page 9)
Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and
position in the assembly sequence. When ordering parts, give Model number, serial number and parts description.
Call or write for current pricing: SFA Companies, 10939 N. Pomona Ave. Kansas City, MO 64153, USA.
13
3
k
j
i
1
p
o
6
12
2
10
l
7
n
h
g
m
b
f
e
11
23R
22
8
d
23L
20
c
9
b
18
21
a
19
14
18
16
15
17
5
4
Figure 4 - Replacement Parts Illustration for Model 29025
8
Replacement Parts List for model 29025
Item#
1
Part#
Description
Qty.
1
1
1
2
2
1
1
1
1
1
1
2
1
2
2
1
3
2
2
1
1
1
1
1
1
G72500-0009
G88002-0015
G72500-0010
G72500-0002
G72500-0003
G07000-0002
G72500-0007
G73500-0021
G48900-0024
G73500-0014
F36100-0001
G49300-0002
G72500-0014
G72500-0015
G72500-0016
G48900-0019
G72500-0017
G48900-0020
G59305-0006
G73500-0011
G73500-0012
G59305-0005
G73500-0016
G73500-0010
G72500-0000
Saddle Pad
2
Saddle
3
Hydraulic Unit
4
Front Wheel Assembly
Rear Caster Assembly
Handle Grip
5
6
7
Handle Assembly
Handle Sleeve
Bolt, M10x16
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23L
23R
**
U-joint
Oil Filler Plug
Return Spring, Lift Arm
Cover
Nut, M16
Spring Washer, D16
Bolt, M12
Nut, M12
Bolt, Handle Sleeve
Spring Washer, D20
Pin D12
Roller
Spring Washer, D10
Left Side Return Spring, Handle
Right Side Return Spring, Handle
Seal Kit (includes a thru p)
-
-
29023-M1
Manual
-
-
29025-L0
Label
**Repair Kit Contents:
Item
Description
O-ring
Qty
1
Item
Description
Qty
2
a
b
c
d
e
f
i
Oil Seal
O-ring
2
j
Back-up Washer
O-ring 13x2.4
O-ring 8x1.8
O-ring 17x2.65
Back-up Washer
O-ring
2
Back-up Washer
U-cup
1
k
l
1
1
1
Back-up Washer
O-ring
1
m
n
o
p
1
1
1
g
h
O-ring
2
1
Washer, Metal
2
Back-up Washer
1
(**) Replacement requires special skills, knowledge, and equipment. Only an authorized service center may
perform the repair and/or replacement of these items.
9
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option,
without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This
limited warranty is a consumer's exclusive remedy.
Performance of any obligation under this warranty may be obtained by returning the warranted product, freight
prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by applicable law,
(1) THE CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF
DEFECTIVE PRODUCTS AS DESCRIBED ABOVE.
(2) SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS
WHATSOEVER.
(3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO ONE YEAR,
OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED
WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
(4)ANY MODIFICATION, ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS
THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights, which vary from state to state.
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
888-332-6419
10
Note Page
Contact:
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
Tel:(888)332-6419 Fax:(816)891-6599
E-Mail:[email protected]
Note Page
Contact:
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
Tel:(888)332-6419 Fax:(816)891-6599
E-Mail:[email protected]
|